Focusing Methods: Using Panoramas We have seen how to implement two methods different focus:
High Pass and Unsharp Mask
, each with their strengths and weaknesses. We also saw how to avoid the noise that arises from the photo focus
LAB mode. But the LAB mode is not the only way to avoid the noise to focus an image, we can achieve very good results if applied before the filters review our photo channel.
For a RGB photo is usually in the blue channel has much more noise than the other two channels. Thus avoiding the blue channel and will be a benefit. But what of the other two channels we use?. There is no fixed rule, we have to do is see each of them and use what has more detail and not make much noise.
Take for example this portrait.
In a normal picture is that the blue channel serving us (much noise) but both the green and red go very well. Here the decision and depends on each one in the green channel tends to be much more detail in the texture of the skin in the red. This can be a good thing if we see a portrait of a man (or if we
Dragan effect ) but must be avoided if the portrait is of a woman because the skin will focus less smooth.
photo Returning to our example we start by analyzing the blue channel (CTRL +3) and we see in dark areas the picture is not is so sharp (I actually look better after comparing with the other channels, but believe me the noise is there.)
The other two channels are much better but they bring different information. Remember, to see the Red channel press CTRL +1 to view the Green CTRL + 2 and return to view full image CTRL + `(on my keyboard is the key to the right of P).
Both channels are perfectly usable for the purpose that we have today (better focus without increasing image noise). But this is a portrait of a woman and the vast majority of the time will be more appreciated if we achieve a smooth skin rather than accentuate the imperfections. Quite the contrary would look for if, for example, the portrait was of an experienced sailor. Clearly this is not a law but it is the most common.
clarify this, what channel it is for us a portrait of a woman? Quick response: the Red. In the pictures above is not possible to differentiate too much, but in the green channel have much more contrast inside the face and rather more about the texture of the skin of our model of the day. However if we look at the contour of the face, eyes and clothing will not find much difference between green and red channel. If we apply the approach to the green channel all that information would be used resulting in less skin soft and silky.
Here I will apply the approach to the high pass filter, but to do it on a channel we must first ensure that we only see the channel we want (CTRL +1/2/3), then select all (CTRL + A) and copy it (CTRL + C). At the moment we copied into memory only the channel you want, create a new layer and paste (CTRL + V). If all went well see a black and white image on the new layer.
From here is the same as it did before
, go to Filter / Other / High Pass and choose the minimum value mark the contours (approximately, the case is not to exceed to avoid white halos). Finally we pass the layer to Soft Light, Hard Light or Overlay as we like better.
And the upshot? This you see below.
The truth is I did not choose the best picture to show it because the resolution is not allowed to appreciate in the page. Anyway I leave here down a 300% increase comparing how the same approach had been using the blue channel and red. If you set the skin of our model has much better tone in the case of the red channel, and the chin area has been better.
Great, I understood but
What happens if there is a picture what I want to focus? If the photo is a portrait and will depend in each case, but there is another trick quite general: CMYK (Cyan, Magenta, Yellow and Black). Conversion to this mode theory is not as straightforward as LAB mode where you can go and return without loss or change some, but not ruin our photo either (just avoid RGB pass and return to eighty times). The trick here is to use the black channel (K) and that we avoid increasing color noise when focusing. It is not eternal salvation but is a trick to keep in mind in difficult cases.
was about to terminate the subject's approach but I remembered that the latest versions of Photoshop added a new filter approach: Smart Sharpen (I forget what they call in Castilian). So before changing the subject briefly see the new filter in the little that I was using very similar to the Unsharp Mask.